LG error codes

Turn off water if leaking is active, then check around the door, drain hose, and base.

Do not use hand dish soap; clear suds with model-approved steps and use dishwasher detergent only.

Use the documented Control Lock button hold for your model rather than forcing panel buttons.

Stop after one safe reset; fan motor conditions need detailed service inspection.

Avoid repeated heated drying attempts and arrange service if F35 returns.

Check for items blocking the door path and request service if the feature remains stuck.

Run one reset and short test only if water fills and drains normally.

Verify the water valve is open and the inlet hose is not kinked.

Check for items blocking spray arms; service is likely if the code returns empty.

Reorganize dishes that may touch moving spray parts and stop if the code returns empty.

Check the drain hose, sink connection, and filter area for restrictions.

Stop after checking for obvious water-level or leak symptoms; PE normally needs service inspection.

Do not keep resetting the dishwasher; temperature sensor faults usually need service.

Fill the steam feeder with tap water to the max line and confirm the drawer is closed.

Hold the model's Child Lock or Control Lock button combination for about 3 seconds.

Clean the lint screen, check the outside vent, and inspect the dryer duct before running another heated cycle.

Stop and verify the full vent path, especially the exterior hood and any crushed duct behind the dryer.

Do not keep restarting heated cycles. Clear or inspect the duct and exterior vent first.

Remove anything caught at the door, close it firmly, and inspect the latch for visible damage.

Check for a kinked, crushed, clogged, or frozen drain hose before another cycle.

Confirm the dryer is on the correct circuit and do not keep resetting a breaker that trips again.

Reset power once and restart the cycle only if the outlet and breaker look normal.

Power reset once; if it returns, the temperature sensing circuit likely needs service.

Protect food and avoid repeated resets; compressor-start diagnosis should be handled by service.

Check door closure, gasket contact, and items blocking drawers before resetting the display.

Do not attempt refrigerant work. Protect food and arrange qualified sealed-system service.

Do not keep resetting or attempt sealed-system work; use qualified service and protect perishable food.

Check only visible bucket and ice-path issues; service is needed if EID remains.

Avoid forcing the ice maker mechanism and use service if the assembly warning stays active.

Keep food safe and use service if the condenser fan warning returns; do not open powered rear covers.

Reset power once only if the unit is dry and stable; service is likely if communication fails again.

Look for heavy frost around visible vents and avoid chipping ice or opening powered evaporator covers.

Record whether the display says freezer or refrigerator defrost sensor and use service if it returns.

Confirm freezer vents are not blocked and avoid removing covers; service is likely if the fan code returns.

Record the code, keep food safe, and use service if the sensor code returns after one reset.

Confirm the water supply is open and stop if water leaks or the flow warning returns.

Check that the ice bucket and freezer air path are clear, then stop if the code returns after one reset.

Move food away from air vents and keep the doors closed while checking whether cooling recovers.

Keep doors closed, monitor cabinet temperature, and use service if the sensor warning returns.

Exit demo mode using the model's documented button sequence and verify the cabinet starts cooling.

Use the model's documented Control Lock or Child Lock button hold to unlock the panel.

Check for clothing caught in the door and inspect the latch area.

Open and close the drawer or door firmly, then stop if the latch area looks damaged.

Restart a short cycle only after the latch area is clear and the door closes normally.

Check for clothing or packaging film blocking the lid or drawer, then close it firmly.

Confirm the paired unit is aligned and stop if the switch or installation looks damaged.

Cancel the cycle and turn off water supply if filling continues.

Open both supply valves fully and check fill hoses for kinks or frozen sections.

Reduce the load, let the washer rest, and retry a short cycle only if the drum moves freely.

Check the drain hose and clean the accessible pump filter before repeating the cycle.

Unplug the washer and arrange service if PE returns, because the water-level sensing path needs diagnosis.

Let the washer reduce suds, then use less HE detergent on the next load.

Disconnect power and request service if the same tE code returns after one reset.

Redistribute heavy items and run a spin test with a balanced load.